SPOT WELD DRILL SROKEN S2000 Spot Weld Drill Re-Grinding MachineHARPENER

 

 

The ROKEN S2000 Spot Weld Drill Re-Grinding Machine is a specialized tool manufactured by BIC TOOL, designed to regrind spot weld cutters, restore cutting sharpness, maintain cutting performance, and extend tool service life. It is suitable for automotive body repair, particularly when working with high-tensile and ultra-high-tensile steel sheets.

 

- Spot Weld Cutter Re-Grinding: Restores the cutting edge of used spot weld cutters, helping reduce the frequency of tool replacement.

- Compatible with Ultra-High-Tensile Steel: When used with the separately sold Gekko Kintaro GK-KIN cutter, the machine supports cutting performance on materials ranging from ordinary steel sheets to ultra-high-tensile steel sheets.

- Simple Operation: The re-grinding process consists of three steps: setting, No. 1 grinding, and No. 2 grinding.

- Wide Grinding Range: Supports cutters with diameters from Ø6.5 mm to Ø10 mm. The Ø6.5 mm grinding function is an additional feature compared with previous models.

- CBN #170 Grinding Wheel: Designed for regrinding specialized spot weld cutters.

- Compact Design: Weighing approximately 8 kg, the machine can be conveniently installed in an automotive body repair workshop.

 

Model: S2000

Brand: ROKEN

Manufacturer: BIC TOOL CO., LTD.

Brand Origin: Japan

Equipment Type: Spot Weld Drill Re-Grinding Machine

Grinding Range: Ø6.5–Ø10.0 mm

Grinding Wheel: CBN #170

Motor Power: 65 W

Power Supply: AC 100 V, 50/60 Hz

Weight: 8 kg

External Dimensions: 225 × 218 × 212 mm (W × D × H)

 

 

Included Accessories:

Holder pipe for Ø6.5 mm cutters

Holder pipe for Ø8.0 mm cutters

Holder pipe for Ø8.2 mm cutters

Holder pipe for Ø10.0 mm cutters

Holder ring

Hex wrench

 

Note: Check the power supply before operation. The product documentation specifies AC 100 V. Confirm that the machine's voltage version is suitable for the electrical system at the installation site.

 

The ROKEN S2000 grinding machine is used for tool maintenance and automotive body repair, including:

- Regrinding spot weld cutters used to remove spot welds from automotive body panels.

- Restoring cutter sharpness to maintain cutting efficiency and reduce the need for frequent tool replacement.

- Supporting the removal of panels made from ordinary steel, high-tensile steel, and ultra-high-tensile steel when used with compatible cutters.

- Use in automotive body and paint workshops, collision repair centers, and automotive body repair facilities.

- Regrinding Gekko Kintaro GK-KIN and GK-KIN150 cutters in accordance with the manufacturer's instructions.

 

According to the manufacturer's published comparison, when cutting 1600 MPa steel sheets at a recommended air drill speed of 1,000–1,200 rpm, the Gekko Kintaro cutter achieved approximately 15–20 holes, compared with approximately 1–1.5 holes for cutters from other manufacturers. These figures are based on the manufacturer's comparison, and actual results may vary depending on operating conditions.

 

Step 1: Prepare the Machine

 

Place the machine on a stable surface and inspect the grinding wheel, holder accessories, and power supply. Read the instruction manual carefully before operation. Wear safety glasses and a dust mask.

 

Step 2: Install and Position the Cutter

 

Select the holder pipe that matches the cutter diameter. Insert and position the cutter in the holder according to the operating instructions and illustrations on the machine label.

 

Step 3: Perform No. 1 Grinding

 

Carry out the first grinding operation according to the machine's operating procedure. For designated Gekko Kintaro GK-KIN cutters, the No. 1 grinding step may be used to restore cutting sharpness as specified in the relevant instructions.

 

Step 4: Perform No. 2 Grinding

 

Complete the second grinding operation according to the manufacturer's instructions to finish the cutting edge. Do not alter the grinding procedure or apply excessive pressure to the cutter.

 

Step 5: Inspect After Grinding

 

Switch off the machine and wait until all rotating parts have come to a complete stop before removing the cutter. Inspect the cutting edge and store the equipment properly after use.

 

Safety Precautions:

- Never touch the grinding wheel or any rotating parts with your hands or body.

- Always wear safety glasses to protect against possible injury from broken fragments.

- Wear a dust mask to reduce inhalation of grinding dust.

- Operate the machine only after reading and understanding the instruction manual.

 

 

 

Why Buy S2000 from KingTech.vn?

🔹 Genuine product from KOKEN-Japan – Guaranteed quality, directly imported.

🔹 12-month warranty – Fast technical support and professional repair services.

🔹 Nationwide shipping – Receive your order in 24-48 hours.

🔹 Best market price – Competitive pricing with attractive promotions.

 

📌 Contact Us Now:

🏢 Kingtech Engineering Corporation

📞 Hotline: 0944 755 799

🌍 Website: KingTech.vn

🚀 ORDER NOW to secure the best price and official warranty for the S2000🔥